meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision Both sides next revision
en:controller:setup [2022/04/06 12:24]
vasilisk [Firmware update] 		en:controller:setup [2022/04/06 12:25]
vasilisk old revision restored (2022/03/19 16:46)
Line 112: Line 112:
 If an error occurs during autotuning, see the section **[[en:controller:diagnostics|Diagnostics of controller malfunctions]]**. In the menu item **Controller** > **Auto-setup** > **Control source** you can select the sources of control for the Controller. See Control Source section below for details**.** \\ If an error occurs during autotuning, see the section **[[en:controller:diagnostics|Diagnostics of controller malfunctions]]**. In the menu item **Controller** > **Auto-setup** > **Control source** you can select the sources of control for the Controller. See Control Source section below for details**.** \\
  
 +===== Firmware update =====
 +
 +In the menu section **Controller** > **Update and Settings**, you can update the Controller's firmware, reset settings, import or export a configuration. You can upload all controller settings to a microSD card. The created file with the name **NCconf.cfg** - **NCconf9.cfg** you can open with the "Notepad" program, see all your settings, make any changes, save. Likewise, you can import a previously saved configuration into the Controller. Trip computer settings cannot be exported or imported. On-board computer settings can be exported and imported in separate [[en:display:start#import_and_export_of_settings|sections]] of the Onboard computer menu. This function is only available in the On-board computer firmware version **0.7B** and higher.
 +
 +{{:en:controller:k3_en.png?nolink |}}
 +
 +**Import config.** — loads the settings from the file ** NCconf.cfg ** - ** NCconf9.cfg ** up to a maximum of 9 different configurations, choosing a file number from 1 to 9. After a successful import, error messages may appear in the message, this means that not all the settings have been imported. In this case, it is advisable to check the downloaded settings with the original file by opening it in Notepad.\\ \\
 +**Export config.** - saves the settings to the ** NCconf.cfg ** - ** NCconf9.cfg ** file up to a maximum of 9 different configurations, choosing a file number from 1 to 9.\\ \\
 +**Reboot** — restarts the device. If the settings have not been saved, they will be reset.\\ \\
 +**Reset Wh usage** — resets the accumulated number of Watt-Hours in the controller. This indicator is displayed in the statistics of the On-board computer, see section **[[en:display:start#statistics|Statistics]]**.\\ \\
 +**Reset stats** — resets mileage in kilometers.\\ \\ 
 +**Load defaults** — after a reset, the default settings are loaded but not saved. If you restart the Controller without saving after a reset, the previous settings will be loaded.\\ \\ 
 +**Erase data storage** — This function may be needed for the correct firmware update, rollback to default settings, in a situation where user actions lead to incorrect operation of the Controller. If the controller has stopped saving the settings, do a reset, wait 3 seconds, and try to save again.\\ \\ 
 +**Update firmware** — starting the firmware update process. You can download the current firmware version and read the rules of update in the **[[en:firmware|Firmware]]** section. To update, download the firmware file to the root directory of the microSD card with the Fat/Fat32 file system. Insert the card with the contacts facing up into the slot on the On-Board Computer and select ** On **. When the update process is complete, a message appears on the screen **Update finished**. Press the left button and check the update version under **Controller** > **Device Information**.
  
 ===== Control modes ===== ===== Control modes =====
Line 428: Line 442:
 The **Controller** > **Motor Setup** menu contains all settings related to electric motor operation parameters. The **Controller** > **Motor Setup** menu contains all settings related to electric motor operation parameters.
  
 +==== Motor temperature sensor ====
 +
 +In the menu section **Controller** > **Motor setup** > **Motor t°-sensor** you can select a temperature range in which a smooth power limit will occur (**Delta °t** parameter) and specify the maximum temperature (**°t max**).
 +
 +{{:en:controller:2_0.8.png?nolink |}}
 +
 +**°t max** — maximum electric motor temperature, in degrees Celsius (°C). Select of values from **50°C** to **200°C**, in increments of **1°C**. \\
 +**Delta °t**  — the temperature value that is deducted from the maximum temperature (**°t max**), the resulting temperature value will be the beginning of the power limit, in degrees Celsius (°C). Select of values from **1°C** to **100°C**, in increments of **1 °C**. \\
 +
 +In the menu item **Sensor type** you can select the following types of temperature sensors that support the controller — **KTY81(82)**, **KTY83**, **KTY84**, **NTC10K (B:3950)**, **NTC10K (B:3380)**, **PT1000**. To disconnect the temperature control, select the value **OFF**.
 +
 +It is recommended to install a temperature sensor so close as possible on the stator windings, while not in contact with the stator iron. If you don't know what kind of sensor is in the motor, you can check all types of sensors and select the one that displays data the most closely to room temperature. The current measured temperature is displayed at **# Value °t #**. \\
 +
 +The **# °t R (+-10%)#** menu item displays the resistance of the motor temperature sensor, with an accuracy of +/-10%.
  
 ==== Clutch ==== ==== Clutch ====
Line 828: Line 856:
 **Speed lim. at 0% throttle**  — enables limiting the speed when the throttle grip is completely released. Select of values **On**  and **Оff**. Selecting **Off**  disables motor control when the throttle is released. **Speed lim. at 0% throttle**  — enables limiting the speed when the throttle grip is completely released. Select of values **On**  and **Оff**. Selecting **Off**  disables motor control when the throttle is released.
  
 +===== Motor setup =====
 +
 +The **Controller**  > **Motor Setup**  menu contains all settings related to electric motor operation parameters.
  
 ==== Motor temperature sensor ==== ==== Motor temperature sensor ====