meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
en:controller:setup [2023/09/30 14:57]
dmitry 		en:controller:setup [2023/10/02 06:26]
vasilisk
Line 578: Line 578:
  
 In the **Controller**  > **Battery**  menu section you can set up the parameters of the battery connected to the Controller. The Nucular controllers support supply voltages from **20V**  to **90V**, this is **21S**  for Lithium-ion (Li-ion) batteries and **25S**  for Lithium-iron-phosphate (LiFePO4) batteries. To configure the battery, you must specify the range of supply voltage and current. To correctly display the battery capacity on the On-board computer screen and correctly calculate the remaining charge, you must specify the battery capacity in [[:en:display:start#battery_capacity|settings]] of On-board Computer. If you use several batteries with different parameters on the same bike, you can save the configurations for each battery on the SD card and load them after replacing the battery. The SD card can be stored in the On-board computer. In the **Controller**  > **Battery**  menu section you can set up the parameters of the battery connected to the Controller. The Nucular controllers support supply voltages from **20V**  to **90V**, this is **21S**  for Lithium-ion (Li-ion) batteries and **25S**  for Lithium-iron-phosphate (LiFePO4) batteries. To configure the battery, you must specify the range of supply voltage and current. To correctly display the battery capacity on the On-board computer screen and correctly calculate the remaining charge, you must specify the battery capacity in [[:en:display:start#battery_capacity|settings]] of On-board Computer. If you use several batteries with different parameters on the same bike, you can save the configurations for each battery on the SD card and load them after replacing the battery. The SD card can be stored in the On-board computer.
- 
-{{:en:controller:k20_en.png?nolink&  }} 
  
 **#Quick voltage setup** — feature to help you select the correct parameters for your battery. To automatically configure the items **Full charge**, **Supply max**, **Supply min**, you need to select the type of battery chemistry from the following options:\\ **#Quick voltage setup** — feature to help you select the correct parameters for your battery. To automatically configure the items **Full charge**, **Supply max**, **Supply min**, you need to select the type of battery chemistry from the following options:\\
-**LiIon (3.6V)** for li-ion battery\\ +**LiIon (3.6V)** for li-ion battery.\\ 
-**LFP (3.2V)** for lithium-iron-phosphate battery (LiFePO4)\\ +**LFP (3.2V)** for lithium-iron-phosphate battery (LiFePO4).\\ 
-**LTO (2.3V)** for lithium-titanate battery (Li4Ti5O12)\\+**LTO (2.3V)** for lithium-titanate battery (Li4Ti5O12).\\
  
 Next, select the **Cell count**, values from **8S** to **28S**, in increments of **1S**. After that, in the **Apply setup** item, select **Yes**. After saving the settings, you will see a window with new battery parameters. It is important to remember that we guarantee the operation of controllers with voltages up to 90V. The device is technically rated for 95V, but operating above 90V will void the warranty and you will be warned about this in a pop-up window. For example, if you try to select 22S for a lithium-ion battery. If the settings exceed 95V, the controller will also warn you that you are trying to set the voltage too high.\\ Next, select the **Cell count**, values from **8S** to **28S**, in increments of **1S**. After that, in the **Apply setup** item, select **Yes**. After saving the settings, you will see a window with new battery parameters. It is important to remember that we guarantee the operation of controllers with voltages up to 90V. The device is technically rated for 95V, but operating above 90V will void the warranty and you will be warned about this in a pop-up window. For example, if you try to select 22S for a lithium-ion battery. If the settings exceed 95V, the controller will also warn you that you are trying to set the voltage too high.\\
Line 810: Line 808:
  **Supply undervoltage**  — too low supply voltage, less than the minimum battery supply threshold. Values **On**  and **Off**. \\  **Supply undervoltage**  — too low supply voltage, less than the minimum battery supply threshold. Values **On**  and **Off**. \\
  **12V protection**  — error on the 12V power line. Values **On**  and **Off**. \\  **12V protection**  — error on the 12V power line. Values **On**  and **Off**. \\
- **Control fail**  — the controller was not able to smoothly turn off the electric motor in time when the brake contacts were closed. Values **On**  and **Off**. **12V protection**  — breaking down or error on the 12V power line. Values **On**  and **Off**. \\+ **Control fail**  — the controller was not able to smoothly turn off the electric motor in time when throttle released. May happen with certain motors when field weakening used, decrease FW current. Values **On**  and **Off**. \\ 
 +**12V protection**  — breaking down or error on the 12V power line. Values **On**  and **Off**. \\
  **Brake error**  — brake lever connection error. Values **On**  and **Off**. \\  **Brake error**  — brake lever connection error. Values **On**  and **Off**. \\
  **Throttle error**  — throttle lever connection error. Values **On**  and **Off**. \\  **Throttle error**  — throttle lever connection error. Values **On**  and **Off**. \\