meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:display:start [2021/12/13 12:33] dmitry [The main screen overview] |
en:display:start [2021/12/13 12:37] dmitry [The main screen overview] |
||
---|---|---|---|
Line 37: | Line 37: | ||
{{: | {{: | ||
- | ==== Data sources setup ==== | + | ===== The main screen overview ===== |
- | In the menu section **Onboard computer** > **Data sources** are configured data sources for various indicators of the Onboard computer. | + | The screenshot below is one of the Main screen configurations. The layout |
- | + | ||
- | {{: | + | |
- | **Current source** — selection of the current source data **Controller** or **BMS**.\\ | + | |
- | **Battery voltage source ** — selection of the battery voltage data source **Controller** or **BMS**.\\ | + | |
- | **Source W/H used.** — select the source of the battery power consumption data **Controller** or **BMS**.\\ | + | |
- | **Wheel circumference** — wheel circumference in millimeters, | + | |
- | **Mileage total** — controller' | + | |
- | + | ||
- | | + | |
- | + | ||
- | **The On-board computer supports two ways to determine the speed:** \\ | + | |
- | — according to information from the Controller.\\ | + | |
- | — by a speed sensor (reed switch), which is connected to the On-board computer. | + | |
- | + | ||
- | If you select the Controller value, the controller readings will be used as the speed data source. This method is suitable for direct-drive or mid-drive motors without overrunning clutch. After selecting the value Controller, you must: | + | |
- | + | ||
- | 1. Specify the number | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | 2. Enable speed calculation (if disabled) in the **Controller** > **Extra parameters** > **Speed calculation** and specify the wheel circumference in millimeters in the **Controller** > **Extra parameters** > **Circumference**. You can use the [[https:// | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | If selecting a value **Display** the speed will be determined from an external sensor, which is used, for example, in a bicycle computer. The speed sensor must be connected according to the diagram to the **SPEED** connector | + | |
- | ==== Password setup ==== | + | |
- | + | ||
- | In the menu section **On-board computer** > **Security** you can set a password that will be requested when turning on the Controller. Without entering the password, the controller will not respond to controls. | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | **Security** — enabling the password request function when starting the controller. Select **Off** and **On**.\\ | + | |
- | **Change password** — changing the default password. | + | |
- | + | ||
- | To set your password, select **On** from the **Security** menu section. Next, go to the menu item **Change password**, you will be asked to enter a password. Enter the default password 1234 by pressing the On-board computer buttons from left to right. Enter a new password, you can assign up to 10 keystrokes. For example, 10 clicks on button 1 or 5 clicks on button 2 and 5 on button 3. After entering the new password, press and hold the right button. Re-enter the new password. Save the settings | + | |
- | + | ||
- | **Attention! There is no way to recover a forgotten password on your own.** Later, the function of recovering the password by the controller serial number will be added. | + | |
- | ==== Firmware update ==== | + | |
- | + | ||
- | In the menu item **On-board computer** > **Update software** you can update the firmware of the On-board computer. You can download the latest firmware version in the [[: | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | | + | |
- | ==== Reset settings ==== | + | |
- | + | ||
- | In the menu section **On-board computer** > **Reset settings**, you can reset all settings to the factory settings. To reset, press the right button of the On-board computer. | + | |
- | ==== Import and export of settings ==== | + | |
- | + | ||
- | In the menu items **On-board computer** > **Export parameters** and **On-board computer** > **Import parameters** you can export and import previously made On-board computer settings to the microSD card. | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | **Import parameters** — import of On-board computer settings configuration from microSD card, file name for import only **NDconf0.cfg**! Click on the right button to import. When importing, a message will be displayed with the number of possible errors, found and accepted parameters. | + | |
- | + | ||
- | | + | |
- | ==== Device information ==== | + | |
- | + | ||
- | In the menu section **On-board computer** > **Device info**, you can view basic data on the On-board computer. In this menu you can check what version of the firmware | + | |
- | + | ||
- | {{: | + | |
- | **HW version** — hardware version.\\ | + | |
- | **HW data** — date of hardware production.\\ | + | |
- | **SW version** — firmware version, you can download the latest firmware in the [[: | + | |
- | **SW data** — firmware compilation date. | + | |
+ | {{: | ||
+ | {{: | ||
+ | Turtle — battery voltage limit. \\ | ||
+ | B! — braking limit. \\ | ||
+ | B — braking. \\ | ||
+ | Motor icon — motor/ | ||
+ | Battery Icon — battery failure. \\ | ||
===== Menu navigation ===== | ===== Menu navigation ===== | ||