meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:display:start [2023/03/10 10:49] dmitry [The main screen overview] |
en:display:start [2023/10/05 11:52] (current) dmitry |
||
---|---|---|---|
Line 1: | Line 1: | ||
~~Title: On-board computer ~~ | ~~Title: On-board computer ~~ | ||
- | ====== On-board computer (v.0.71B) ====== | + | ====== On-board computer (v0.82B) ====== |
- | The On-board computer is equipped with a large sunlight resistant screen to display main parameters, driving modes settings, software updates for all system components, battery control, and the charging state of the devices via USB. On the left side of the On-board computer there is a slot for a microSD card, which is used to update the firmware, save screenshots, | + | The On-board computer is equipped with a large sunlight-resistant screen to display main parameters, driving modes settings, software updates for all system components, battery control, and the charging state of the devices via USB. On the left side of the On-board computer there is a slot for a microSD card, which is used to update the firmware, save screenshots, |
//Technical specifications:// | //Technical specifications:// | ||
Line 122: | Line 122: | ||
**IO7 state** | **IO7 state** | ||
**IO8 state** | **IO8 state** | ||
- | **CAN_OVR** | + | **CAN_OVR** |
- | **CAN_TEC** | + | **CAN_LEC** |
+ | * 0: No Error | ||
+ | * 1: Stuff Error | ||
+ | * 2: Form Error | ||
+ | * 3: Acknowledgment Error | ||
+ | * 4: Bit recessive Error | ||
+ | * 5: Bit dominant Error | ||
+ | * 6: CRC Error | ||
+ | **CAN_TEC** | ||
+ | **CAN_REC** | ||
==== Settings saving ==== | ==== Settings saving ==== | ||
Line 185: | Line 194: | ||
{{: | {{: | ||
~~CL~~ \\ | ~~CL~~ \\ | ||
- | ==== Speed unit ==== | + | ==== Temperature graphs |
- | In the menu **On-board computer** > **Main screen setup** > **Speed unit**, you can select | + | For temperature graphs, you can configure |
- | ==== Temperature graphs ==== | + | {{: |
+ | **Start motor t°** — minimum displayed motor temperature in degrees Celsius (**°C**), values from **5**°C to **250**°C, in **5**°C increments. \\ | ||
+ | **End motor t°** — maximum displayed motor temperature in degrees Celsius (**°C**), values from **5**°C to **250**°C, in **5**°C increments. \\ | ||
+ | **Start controller t°** — minimum displayed controller temperature in degrees Celsius (**°**C), values from **5**°C to **250**°C, in **5**°C increments. \\ | ||
+ | **End controller t°** — maximum displayed controller temperature in degrees Celsius (**°C**), values from **5**°C to **250**°C, in **5**°C increments. \\ | ||
+ | **Start phase current** — minimum displayed current in Amps (**A**), selectable from **5**A to **500**A, in **5A** increments. \\ | ||
+ | **End phase current** — maximum displayed current in Amps (**A**), selectable from **5**A to **500**A, in **5A** increments. \\ | ||
+ | ~~CL~~ \\ | ||
- | For temperature graphs, you can configure the display limits, through the parameters in the section **On-board computer** > **Main screen setup**. If several controllers are connected, the highest temperature of the motor or controller will be displayed. After making changes, you must go to the **On-board computer** > **Save** and save settings. | ||
- | {{: | + | ==== Units of measure ==== |
+ | |||
+ | In the menu **On-board computer** > **Main screen setup** you can select units for speed and temperature. After making changes, you must go to the **On-board computer** > **Save** and save settings. \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Speed unit** — in kilometers per hour (**km_h**) or in miles per hour (**mph**). \\ | ||
+ | **Temperature unit** — in degrees Celsius (**°C**) or degrees | ||
~~CL~~ \\ | ~~CL~~ \\ | ||
+ | |||
==== Battery capacity ==== | ==== Battery capacity ==== | ||
In the menu **On-board computer** > **Main screen setup** > **Battery capacity** configures the display of the battery capacity on the Main screen. After making changes, you must go to the **On-board computer** > **Save** and save settings. | In the menu **On-board computer** > **Main screen setup** > **Battery capacity** configures the display of the battery capacity on the Main screen. After making changes, you must go to the **On-board computer** > **Save** and save settings. | ||
- | {{: | + | {{: |
+ | |||
+ | **Battery capacity** — the energy stored by the battery, in Watt-hours (W*h), the values from **5** W*h to **10000** W*h, with increments of **5** W*h. | ||
~~CL~~ \\ | ~~CL~~ \\ | ||
==== Main screen theme ==== | ==== Main screen theme ==== | ||
Line 226: | Line 251: | ||
In the menu **On-board computer** > **Main screen setup** > **Demo mode** you can turn on the animation of the status bars on the main screen when starting the On-board computer. Select values **On** and **Off**. \\ | In the menu **On-board computer** > **Main screen setup** > **Demo mode** you can turn on the animation of the status bars on the main screen when starting the On-board computer. Select values **On** and **Off**. \\ | ||
- | |||
Line 306: | Line 330: | ||
If selecting a value **Display** the speed will be determined from an external sensor, which is used, for example, in a bicycle computer. The speed sensor must be connected according to the diagram to the **SPEED** connector on the rear panel of the On-board computer. After setting the Display value and connecting the speed sensor, you must specify the wheel circumference in millimeters in the **On-board computer** > **Data source menu**. \\ | If selecting a value **Display** the speed will be determined from an external sensor, which is used, for example, in a bicycle computer. The speed sensor must be connected according to the diagram to the **SPEED** connector on the rear panel of the On-board computer. After setting the Display value and connecting the speed sensor, you must specify the wheel circumference in millimeters in the **On-board computer** > **Data source menu**. \\ | ||
- | ==== Password | + | ==== Security and password |
In the menu section **On-board computer** > **Security** you can set a password that will be requested when turning on the Controller. Without entering the password, the controller will not respond to controls. | In the menu section **On-board computer** > **Security** you can set a password that will be requested when turning on the Controller. Without entering the password, the controller will not respond to controls. | ||
- | {{: | + | {{: |
+ | **Switch-on password** — enabling the password request when starting the controller. Select **Off** and **On**. The password is set under **Change password** — changing the default password. To set your password, go to **Change password**, you will be prompted to enter your password. Enter the default password **1234** by pressing the On-board computer buttons from left to right. Enter a new password, you can assign up to 10 keystrokes. For example, 10 clicks on button 1 or 5 clicks on button 2 and 5 on button 3. After entering the new password, press and hold the right button. Re-enter the new password. Save the settings in the menu **On-board computer** > **Save** to save the new password. | ||
- | **Security** | + | **Attention! There is no way to recover a forgotten password on your own.** Later, |
- | **Change | + | |
- | To set your password, | + | **Device |
- | **Attention! There is no way to recover a forgotten | + | **Main screen password** — enable the password request when trying |
+ | |||
+ | **Change master password** — sets the master password that is used to set the **Device password** and **Main screen password**. The same password is used for both settings. To set your password, go to **Change master password**, you will be prompted to enter your password. Enter the default password **1234** by pressing the On-board computer buttons from left to right. Enter a new password, you can assign up to 10 keystrokes. For example, 10 clicks on button 1 or 5 clicks on button 2 and 5 on button 3. After entering the new password, press and hold the right button. Re-enter the new password. Save the settings in the menu **On-board computer** > **Save** to save the new password. \\ | ||
+ | |||
+ | **Stat. speed limit** — limiting the maximum speed value that will be displayed in the On-board computer statistics. Values from **1** to **255**, in increments of **1**. | ||
==== Firmware update ==== | ==== Firmware update ==== | ||
- | In the menu item **On-board computer** > **Update | + | In the menu item **On-board computer** > **Update |
- | {{: | + | {{: |
~~CL~~ \\ | ~~CL~~ \\ | ||
+ | |||
+ | In the menu item **On-board computer** > **Update and settings** > **Forced update of devices** you can force a firmware update of any device visible in the **Setting** > **Devices** menu without having to go to the menu of each device separately to update it. This function will also be useful if you have updated the On-board computer to the latest firmware, and the Controller has firmware v.7.18 (and lower) and is not visible in the **Setting** > **Devices** menu due to the new protocol. \\ | ||
+ | |||
+ | To update, download the firmware file to the root directory of the microSD card with Fat/Fat32 file system. Insert the card, with the contacts on top, into the connector on the On-board Computer. After that, go to the menu item **On-board computer** > **Update and settings** > **Forced update of devices** and select the device you want to update. Press the right button on On-board Computer to start the update. After restarting, check the firmware version under **On-board Computer** > **Device Information**. | ||
+ | ~~CL~~ \\ | ||
+ | |||
==== Reset settings ==== | ==== Reset settings ==== | ||
- | In the menu section **On-board computer** > **Reset settings**, you can reset all settings to the factory settings. To reset, press the right button of the On-board computer. \\ | + | In the menu section **On-board computer** > **Update and settings** > **Reset settings**, you can reset all settings to the factory settings. To reset, press the right button of the On-board computer. \\ |
==== Import and export of settings ==== | ==== Import and export of settings ==== | ||
- | In the menu items **On-board computer** > **Export parameters** and **On-board computer** > **Import parameters** you can export and import previously made On-board computer settings to the microSD card. | + | In the menu items **On-board computer** > **Update and settings** > **Export parameters** and **On-board computer** > **Update and settings** > **Import parameters** you can export and import previously made On-board computer settings to the microSD card. |
{{: | {{: | ||
Line 349: | Line 383: | ||
**SW data** — firmware compilation date. | **SW data** — firmware compilation date. | ||
+ | ==== Memory ==== | ||
+ | |||
+ | In the menu section **On-board computer** > **Update and settings** are the menu items for working with memory of the On-board computer. | ||
+ | **Save dump** — copying information about the state of the system (memory dump) to an SD card. This function is used by developers to find errors in the device code. \\ | ||
+ | **Erage storage** — erase the memory and all settings of the On-board computer. \\ |