meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:firmware [2020/10/09 10:56] vasilisk |
en:firmware [2022/01/30 14:28] dmitry old revision restored (2022/01/20 17:22) |
||
---|---|---|---|
Line 1: | Line 1: | ||
~~Title: Firmware~~ | ~~Title: Firmware~~ | ||
- | Copy files to root directory of microSD card (filesystem FAT32), insert into display | + | Copy files to root directory of microSD card (filesystem FAT32), insert into On-board computer |
<WRAP important 60%>\\ | <WRAP important 60%>\\ | ||
- | **Do not downgrade firmware that was installed | + | **Do not downgrade firmware that was installed |
- | Every device have own firmware! Display updated in display menu, controller updates through controller menu. | + | |
- | |**Display** |**Controller** |**Release notes** | | + | Each device has its own firmware and is updated separately from different menus. It does not matter in what order you update the firmware of the devices. If you have older firmware, you can install the latest firmware at once, without having to install the firmware one by one.\\ |
- | |v0.60B [[https:// | + | 1. [[en: |
- | |v0.59B {{: | + | 2. [[en: |
- | |v0.58B {{: | + | 3. [[en: |
- | | |v0.7.9 {{: | + | |
- | |v0.57B {{: | + | To check the current firmware version, go to the **Device Information** menu, each device has a separate menu.\\ |
+ | 1. [[en: | ||
+ | 2. [[en: | ||
+ | 3. [[en: | ||
+ | |||
+ | The list of actual firmware to be downloaded: \\ | ||
+ | ===== 20 January 2022 ===== | ||
+ | |||
+ | Critical update for new controllers and hotfix for controllers 6F/12F and old 24F. Export config before the update, load defaults after the update, and import your config. \\ | ||
+ | |||
+ | **Controller | ||
+ | |||
+ | < | ||
+ | |||
+ | Save system updated, added unit tests. \\ | ||
+ | Added clutch shutdown when brake pressed. \\ | ||
+ | Added option to enable MTPA. \\ | ||
+ | USB for computers disabled by default, will be removed in the future | ||
+ | Fixed P1 P2 PWM mode.\\ | ||
+ | Lifetime temperature now calculates only when motor powered.\\ | ||
+ | Added hall pullup disable option.\\ | ||
+ | Various save system fixes.\\ | ||
+ | Fixed NaN for resistance detection.\\ | ||
+ | Fixed import of 1st parameter in every section.\\ | ||
+ | \\ | ||
+ | Hotfix for 6F/12F and old 24F. | ||
+ | </ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== 18 October 2021 ===== | ||
+ | First need to update all devices but display. Because menu protocol is new and old devices will not be visible in menu. After update finished hold left button few seconds to exit updated device menu. If button does not work you may need to reset power supply or replug CAN cable in display. \\ After everything updated - update display. \\ Make a controller reset (load defaults) after update. \\ I recommend to run motor detect again on controllers. \\ Detection of throttle/ | ||
+ | |||
+ | **Display v0.71B** [[https:// | ||
+ | |||
+ | **Controller v0.8.2** [[https:// | ||
+ | |||
+ | **uLight v0.6.1** [[https:// | ||
+ | |||
+ | ===== 31 August 2020 ===== | ||
+ | Use configuration export before update, reset defaults after update and import configuration. \\ | ||
+ | **Display | ||
+ | Fixed throttle drop. \\ Small menu fixes. \\ LEVCAN updated. \\ Button setup simplified, by default all set to CAN mode. \\ Added exFAT support (but display still can be updated only from FAT32). \\ Added charge screen. \\ Added fast statistics type selection. \\ Added wider event window. \\ Mph stats fixed. | ||
+ | </ | ||
+ | **Controller | ||
+ | \\ | ||
+ | |||
+ | ===== 18 March 2020 ===== | ||
+ | **Display | ||
+ | \\ HOTFIX for display speed sensor | ||
+ | |||
+ | ===== 11 March 2020 ===== | ||
+ | **Display | ||
+ | Fixed 0V throttle issue. \\ Fixed charge statistics reset. \\ Added kmh/mph switch. \\ Added more parameters to info. lines on main screen. \\ Added hotkey mode for compatibility with controller speed functions. \\ Fixed contrast setting. \\ Added driving range, calculated from WH usage. \\ A lot of tiny fixes.</ | ||
+ | **Controller | ||
+ | |||
+ | ===== 21 Nov 2019 ===== | ||
+ | HOTFIX, fixed NaN error for analog inputs. \\ | ||
+ | **Controller | ||
+ | |||
+ | ===== 20 Nov 2019 ===== | ||
+ | Export configuration (or make screenshots), after controller update do "Erase data storage" | ||
+ | **Display | ||
+ | CAN buttons setup \\ Inverted inputs setup \\ Statistics reworked \\ Added filters for analog inputs | ||
+ | </ | ||
+ | **Controller | ||