meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:firmware [2021/09/14 17:28] dmitry |
en:firmware [2022/01/06 14:55] dmitry [30 December 2021] |
||
---|---|---|---|
Line 5: | Line 5: | ||
**Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </ | **Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </ | ||
- | Each device has its own firmware and is updated separately from different menus. | + | Each device has its own firmware and is updated separately from different menus. |
1. [[en: | 1. [[en: | ||
2. [[en: | 2. [[en: | ||
- | 3. [[en: | + | 3. [[en: |
To check the current firmware version, go to the **Device Information** menu, each device has a separate menu.\\ | To check the current firmware version, go to the **Device Information** menu, each device has a separate menu.\\ | ||
- | 1https:// | + | 1. [[en: |
2. [[en: | 2. [[en: | ||
- | 3. [[en: | + | 3. [[en: |
- | The list of actual firmware to be downloaded: | + | The list of actual firmware to be downloaded: |
+ | ===== 30 December 2021 ===== | ||
+ | Critical update for new controllers and hotfix for controllers 6F/12F and old 24F. \\ | ||
- | |**Display** |**Controller** |**Release notes** | | + | **Controller v0.8.4** [[https:// |
- | |v0.60B [[https:// | + | |
+ | < | ||
+ | |||
+ | Critical update for new controllers: | ||
+ | Save system updated, added unit tests. \\ | ||
+ | Added clutch shutdown when brake pressed. \\ | ||
+ | Added option to enable MTPA. \\ | ||
+ | USB for computers disabled by default, will be removed in the future. \\ | ||
+ | \\ | ||
+ | Hotfix for 6F/12F and old 24F. \\ | ||
+ | </ | ||
+ | \\ | ||
+ | ===== 18 October 2021 ===== | ||
+ | First need to update all devices but display. Because menu protocol is new and old devices will not be visible in menu. After update finished hold left button few seconds to exit updated device menu. If button does not work you may need to reset power supply or replug CAN cable in display. \\ After everything updated - update display. \\ Make a controller reset (load defaults) after update. \\ I recommend to run motor detect again on controllers. \\ Detection of throttle/ | ||
+ | |||
+ | **Display | ||
+ | |||
+ | **Controller | ||
+ | |||
+ | **uLight v0.6.1** [[https:// | ||
+ | |||
+ | ===== 31 August 2020 ===== | ||
+ | Use configuration export before update, reset defaults after update and import configuration. \\ | ||
+ | **Display | ||
Fixed throttle drop. \\ Small menu fixes. \\ LEVCAN updated. \\ Button setup simplified, by default all set to CAN mode. \\ Added exFAT support (but display still can be updated only from FAT32). \\ Added charge screen. \\ Added fast statistics type selection. \\ Added wider event window. \\ Mph stats fixed. | Fixed throttle drop. \\ Small menu fixes. \\ LEVCAN updated. \\ Button setup simplified, by default all set to CAN mode. \\ Added exFAT support (but display still can be updated only from FAT32). \\ Added charge screen. \\ Added fast statistics type selection. \\ Added wider event window. \\ Mph stats fixed. | ||
- | </ | + | </ |
- | |v0.59B [[https:// | + | **Controller |
- | |v0.58B [[https:// | + | \\ |
- | Fixed 0V throttle issue. \\ Fixed charge statistics reset. \\ Added kmh/mph switch. \\ Added more parameters to info. lines on main screen. \\ Added hotkey mode for compatibility with controller speed functions. \\ Fixed contrast setting. \\ Added driving range, calculated from WH usage. \\ A lot of tiny fixes. | + | |
- | </ | + | ===== 18 March 2020 ===== |
- | | |v0.7.9 [[https:// | + | **Display |
- | |v0.57B [[https:// | + | \\ HOTFIX for display speed sensor |
+ | |||
+ | ===== 11 March 2020 ===== | ||
+ | **Display | ||
+ | Fixed 0V throttle issue. \\ Fixed charge statistics reset. \\ Added kmh/mph switch. \\ Added more parameters to info. lines on main screen. \\ Added hotkey mode for compatibility with controller speed functions. \\ Fixed contrast setting. \\ Added driving range, calculated from WH usage. \\ A lot of tiny fixes.</ | ||
+ | **Controller | ||
+ | |||
+ | ===== 21 Nov 2019 ===== | ||
+ | HOTFIX, fixed NaN error for analog inputs. \\ | ||
+ | **Controller | ||
+ | |||
+ | ===== 20 Nov 2019 ===== | ||
+ | Export configuration (or make screenshots), after controller update do "Erase data storage" | ||
+ | **Display | ||
CAN buttons setup \\ Inverted inputs setup \\ Statistics reworked \\ Added filters for analog inputs | CAN buttons setup \\ Inverted inputs setup \\ Statistics reworked \\ Added filters for analog inputs | ||
- | </ | + | </ |
+ | **Controller | ||