meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:firmware [2021/09/14 17:29] dmitry |
en:firmware [2022/01/30 14:33] dmitry [18 October 2021] |
||
---|---|---|---|
Line 5: | Line 5: | ||
**Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </ | **Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </ | ||
- | Each device has its own firmware and is updated separately from different menus. | + | Each device has its own firmware and is updated separately from different menus. |
1. [[en: | 1. [[en: | ||
2. [[en: | 2. [[en: | ||
- | 3. [[en: | + | 3. [[en: |
To check the current firmware version, go to the **Device Information** menu, each device has a separate menu.\\ | To check the current firmware version, go to the **Device Information** menu, each device has a separate menu.\\ | ||
- | 1. [[en: | + | 1. [[en: |
2. [[en: | 2. [[en: | ||
- | 3. [[en: | + | 3. [[en: |
- | The list of actual firmware to be downloaded: | + | The list of actual firmware to be downloaded: |
+ | ===== 20 January 2022 ===== | ||
- | |**Display** |**Controller** |**Release notes** | | + | Critical update for new controllers and hotfix for controllers 6F/12F and old 24F. Export config before the update, load defaults after the update, and import your config. \\ |
- | |v0.60B [[https:// | + | |
+ | **Controller v0.8.5** [[https:// | ||
+ | |||
+ | < | ||
+ | |||
+ | Save system updated, added unit tests. \\ | ||
+ | Added clutch shutdown when brake pressed. \\ | ||
+ | Added option to enable MTPA. \\ | ||
+ | USB for computers disabled by default, will be removed in the future | ||
+ | Fixed P1 P2 PWM mode.\\ | ||
+ | Lifetime temperature now calculates only when motor powered.\\ | ||
+ | Added hall pullup disable option.\\ | ||
+ | Various save system fixes.\\ | ||
+ | Fixed NaN for resistance detection.\\ | ||
+ | Fixed import of 1st parameter in every section.\\ | ||
+ | \\ | ||
+ | Hotfix for 6F/12F and old 24F. | ||
+ | </ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== 18 October 2021 ===== | ||
+ | First, need to update all devices but display. Because menu protocol is new and old devices will not be visible in menu. After the update is finished hold the left button few seconds to exit the updated device menu. If the button does not work you may need to reset the power supply or replug CAN cable in the On-board computer. After everything is updated — update the On-board computer. Make a controller reset (load defaults) after the update. We recommend running motor detects again on controllers. Detection of throttle/ | ||
+ | |||
+ | **Display | ||
+ | |||
+ | **Controller | ||
+ | |||
+ | **uLight v0.6.1** [[https:// | ||
+ | |||
+ | ===== 31 August 2020 ===== | ||
+ | Use configuration export before update, reset defaults after update and import configuration. \\ | ||
+ | **Display | ||
Fixed throttle drop. \\ Small menu fixes. \\ LEVCAN updated. \\ Button setup simplified, by default all set to CAN mode. \\ Added exFAT support (but display still can be updated only from FAT32). \\ Added charge screen. \\ Added fast statistics type selection. \\ Added wider event window. \\ Mph stats fixed. | Fixed throttle drop. \\ Small menu fixes. \\ LEVCAN updated. \\ Button setup simplified, by default all set to CAN mode. \\ Added exFAT support (but display still can be updated only from FAT32). \\ Added charge screen. \\ Added fast statistics type selection. \\ Added wider event window. \\ Mph stats fixed. | ||
- | </ | + | </ |
- | |v0.59B [[https:// | + | **Controller |
- | |v0.58B [[https:// | + | \\ |
- | Fixed 0V throttle issue. \\ Fixed charge statistics reset. \\ Added kmh/mph switch. \\ Added more parameters to info. lines on main screen. \\ Added hotkey mode for compatibility with controller speed functions. \\ Fixed contrast setting. \\ Added driving range, calculated from WH usage. \\ A lot of tiny fixes. | + | |
- | </ | + | ===== 18 March 2020 ===== |
- | | |v0.7.9 [[https:// | + | **Display |
- | |v0.57B [[https:// | + | \\ HOTFIX for display speed sensor |
+ | |||
+ | ===== 11 March 2020 ===== | ||
+ | **Display | ||
+ | Fixed 0V throttle issue. \\ Fixed charge statistics reset. \\ Added kmh/mph switch. \\ Added more parameters to info. lines on main screen. \\ Added hotkey mode for compatibility with controller speed functions. \\ Fixed contrast setting. \\ Added driving range, calculated from WH usage. \\ A lot of tiny fixes.</ | ||
+ | **Controller | ||
+ | |||
+ | ===== 21 Nov 2019 ===== | ||
+ | HOTFIX, fixed NaN error for analog inputs. \\ | ||
+ | **Controller | ||
+ | |||
+ | ===== 20 Nov 2019 ===== | ||
+ | Export configuration (or make screenshots), after controller update do "Erase data storage" | ||
+ | **Display | ||
CAN buttons setup \\ Inverted inputs setup \\ Statistics reworked \\ Added filters for analog inputs | CAN buttons setup \\ Inverted inputs setup \\ Statistics reworked \\ Added filters for analog inputs | ||
- | </ | + | </ |
+ | **Controller | ||