meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:ulight [2022/04/18 09:58] dmitry [Inputs configuration] |
en:ulight [2022/09/01 14:30] dmitry [Connection] |
||
---|---|---|---|
Line 13: | Line 13: | ||
* //2 digital outputs// | * //2 digital outputs// | ||
* //3 CAN bus connectors// | * //3 CAN bus connectors// | ||
- | |||
//In the kit:// | //In the kit:// | ||
Line 27: | Line 26: | ||
You can look at the connection diagrams for other devices at this [[https:// | You can look at the connection diagrams for other devices at this [[https:// | ||
- | {{:en:ulight_diagram.png? | + | {{:en:ulight_en_0109_2.png? |
+ | |||
+ | ~~CL~~ | ||
+ | \\ | ||
Connecting uLight to the Controller and the On-Board computer is possible in different ways: | Connecting uLight to the Controller and the On-Board computer is possible in different ways: | ||
Line 46: | Line 48: | ||
==== Save settings ==== | ==== Save settings ==== | ||
+ | |||
Saving all settings made. Select **On** | Saving all settings made. Select **On** | ||
==== Firmware updates ==== | ==== Firmware updates ==== | ||
+ | |||
Section for working with firmware updates and settings. | Section for working with firmware updates and settings. | ||
{{: | {{: | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
==== Inputs configuration ==== | ==== Inputs configuration ==== | ||
- | The functions of inputs **I1-I6 ** (see diagram above) are selected in the **Function setup** | + | |
- | \\ {{: | + | The functions of inputs **I1-I6 ** (see diagram above) are selected in the **Function setup** |
- | **T-sensor T1 type** | + | |
- | **T-sensor T1** — displays the temperature of the temperature | + | {{: |
- | **T-sensor T2 type** — similar to the **T-sensor T1 type** | + | |
- | **T-sensor T2** | + | |
- | **CAN-Control **— this setting refers to the **THR** | + | |
==== Function setup ==== | ==== Function setup ==== | ||
- | Function setup allows you to select which function each input on the uLight board or CAN input in the Controller or On-board computer corresponds to. All settings in this section of the menu have the same selection of functions: \\ **Off **— disabled. \\ **On** | + | |
+ | Function setup allows you to select which function each input on the uLight board or CAN input in the Controller or On-board computer corresponds to. All settings in this section of the menu have the same selection of functions: \\ **Off **— disabled. \\ **On** | ||
{{: | {{: | ||
Line 69: | Line 73: | ||
**Shutdown by CAN** — this setting allows you to turn off all lighting equipment if you turned off the Controller but didn't turn off the power supply to the uLight board. The shutdown signal will be transmitted via the CAN bus and all lighting equipment will be turned off. The default is **Off** | **Shutdown by CAN** — this setting allows you to turn off all lighting equipment if you turned off the Controller but didn't turn off the power supply to the uLight board. The shutdown signal will be transmitted via the CAN bus and all lighting equipment will be turned off. The default is **Off** | ||
- | **# Turn signals setup #** \\ | + | **# Turn signals setup #** \\ Settings for the left and right turn signals. Read more about the setup below in the section **Turn signals setup**. \\ **Left turn switch** |
- | Settings for the left and right turn signals. Read more about the setup below in the section **Turn signals setup**. \\ **Left turn switch** | + | |
- | **# Brake signal setup #** \\ | + | **# Brake signal setup #** \\ The brake signal is adjustable in two brightness levels. \\ **Off-brake brightness** |
- | The brake signal is adjustable in two brightness levels. \\ **Off-brake brightness** | + | |
- | **# Reverse signal setup #** \\ | + | **# Reverse signal setup #** \\ Adjust the brightness of the light of reverse. The uLight board does not have an input for the switch of reverse, therefore, this function is controlled from a switch connected to the On-board computer or Controller. When the Controller is turn on reverse, the signal on the uLight board will also be active. \\ **Off-revers bright.** |
- | Adjust the brightness of the light of reverse. The uLight board does not have an input for the switch of reverse, therefore, this function is controlled from a switch connected to the On-board computer or Controller. When the Controller is turn on reverse, the signal on the uLight board will also be active. \\ **Off-revers bright.** | + | |
**# Beam setup #** \\ **Low beam switch** | **# Beam setup #** \\ **Low beam switch** | ||
- | **# Horn setup #** \\ | + | **# Horn setup #** \\ A horn can be connected to the uLight board, if necessary. \\ **Horn switch** |
- | A horn can be connected to the uLight board, if necessary. \\ **Horn switch** | + | |
- | **# Fan control #** \\ | + | **# Fan control #** \\ Fan control allows you to adjust the cooling of the motor or Controller or using other scenarios using temperature sensors. Two temperature sensors can be connected to the uLight board. The setup menus for all temperature sensors are the same. \\ **Motor T-sensor **— motor temperature sensor. \\ **Controller T-sensor** |
- | Fan control allows you to adjust the cooling of the motor or Controller or using other scenarios using temperature sensors. Two temperature sensors can be connected to the uLight board. The setup menus for all temperature sensors are the same. \\ **Motor T-sensor **— motor temperature sensor. \\ **Controller T-sensor** | + | |
The setup menus for all temperature sensors are the same. Below is a description of the menu using the example of a **T1 T-sensor**. | The setup menus for all temperature sensors are the same. Below is a description of the menu using the example of a **T1 T-sensor**. | ||
Line 91: | Line 90: | ||
**Temperature min** — minimum temperature, | **Temperature min** — minimum temperature, | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
==== Output configuration ==== | ==== Output configuration ==== | ||
- | In this section, you can configure which output each function belongs to. The uLight has six power outputs **OUT1-OUT6** | ||
- | **Output 1** — setting the function | + | In this section, you can configure which output each function |
- | **Output | + | **Output |
- | The frequency of **PWM 3-4** and **PWM 5-6** and their outputs | + | **Output |
- | There is an **IO1** port on the uLight, in which there are four low-power PWM outputs **O1-O4**. They can connect, for example, an optocoupler. In the menu, you can select the mode of operation of the PWM at the outputs, its frequency, and the value of the function for each output. Outputs **O1** | + | |
- | **PWM IO mode **— is a setting | + | The frequency of **PWM 3-4** and **PWM 5-6** and their outputs **Output 3-6** are configured in the same way. \\ \\ There is an **IO1** |
- | **PWM IO freq** — is a setting for advanced users. Selecting the frequency values | + | **PWM IO mode **— is a setting for advanced users. Selecting the PWM mode of the **IO** |
- | **Output P1** — setting the function of the PWM output of the low power **IO1** | + | **PWM IO freq** |
+ | |||
+ | **Output P1** — setting the function of the PWM output of the low power **IO1** | ||
**Outputs P3-P4** | **Outputs P3-P4** | ||
+ | |||
==== Input values ==== | ==== Input values ==== | ||
- | In this section of the menu you can see the values of the indicators at each input of the uLight board. This menu is similar to the **Debug information** | + | |
- | **Current** | + | In this section of the menu you can see the values of the indicators at each input of the uLight board. This menu is similar to the **Debug information** |
- | **Voltage** | + | |
- | **Throttle** | + | ~~CL~~ |
- | **Brake** | + | |
- | **T-sensor internal** | + | |
- | **T-sensor T1** — temperature at the external temperature sensor T1 connected to the uLight board, degrees Celsius (**°C**). \\ | + | |
- | **T-sensor T2** — temperature at the external temperature sensor T1 connected to the uLight board, degrees Celsius (**°C**). \\ | + | |
- | **Input I1-Input I6** — values of buttons or switches connected to the uLight board, **Off** | + | |
- | ~~CL~~ | + | |
==== Device information ==== | ==== Device information ==== | ||
- | Basic information about the uLight controller. In this menu, you can see what version of the firmware is loaded into your uLight controller. \\ \\ {{: | + | |
- | ~~CL~~ | + | Basic information about the uLight controller. In this menu, you can see what version of the firmware is loaded into your uLight controller. \\ \\ {{: |
+ | **Loader date** | ||
+ | |||
+ | ~~CL~~ | ||
===== Settings examples ===== | ===== Settings examples ===== | ||
Line 137: | Line 137: | ||
Connect the headlamp according to the diagram (see above) to one of the **OUT1-OUT6** | Connect the headlamp according to the diagram (see above) to one of the **OUT1-OUT6** | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
=== Control from external buttons of the switch connected to the uLight board === | === Control from external buttons of the switch connected to the uLight board === | ||
Line 143: | Line 144: | ||
After connecting the headlight power supply, need to connect an external switch to the uLight board to control the headlight. For connection according to the diagram (see above) use inputs **I3-I4** | After connecting the headlight power supply, need to connect an external switch to the uLight board to control the headlight. For connection according to the diagram (see above) use inputs **I3-I4** | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Function setup == | == Function setup == | ||
Line 150: | Line 152: | ||
You need to go to the **Function setup** | You need to go to the **Function setup** | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Output setup == | == Output setup == | ||
Line 157: | Line 160: | ||
Go to the **Outputs configuration** | Go to the **Outputs configuration** | ||
- | {{: | + | {{: |
Then return to the main menu, go to the **Save settings** | Then return to the main menu, go to the **Save settings** | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
=== Control from external buttons of the switch connected to the On-board computer === | === Control from external buttons of the switch connected to the On-board computer === | ||
Line 166: | Line 170: | ||
After connecting the power supply for the headlight power supply, need to connect an external headlight control switch to the On-board computer. For connection according to the [[https:// | After connecting the power supply for the headlight power supply, need to connect an external headlight control switch to the On-board computer. For connection according to the [[https:// | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Setup inputs in the On-board computer == | == Setup inputs in the On-board computer == | ||
- | Need to go to the On-board computer menu and go to the **Button setup** [[https:// | + | Need to go to the On-board computer menu and go to the **Button setup** |
- | {{: | + | {{: |
Next, select which input the **High beam button** | Next, select which input the **High beam button** | ||
After all the settings, go to the **Save settings** | After all the settings, go to the **Save settings** | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Setup functions in the uLight == | == Setup functions in the uLight == | ||
Line 184: | Line 190: | ||
You need to go to the **Function setup** | You need to go to the **Function setup** | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Output setup == | == Output setup == | ||
Line 191: | Line 198: | ||
Go to the **Output configuration** | Go to the **Output configuration** | ||
- | {{: | + | {{: |
Then return to the main menu, go to the **Save settings** | Then return to the main menu, go to the **Save settings** | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
=== Control from the buttons on the On-board computer === | === Control from the buttons on the On-board computer === | ||
Line 200: | Line 208: | ||
After connecting the headlight power supply, it is necessary to configure the On-board computer buttons. Go to the menu **On-board computer** | After connecting the headlight power supply, it is necessary to configure the On-board computer buttons. Go to the menu **On-board computer** | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Setup functions in the uLight == | == Setup functions in the uLight == | ||
Line 207: | Line 216: | ||
You need to go to the **Functions setup** | You need to go to the **Functions setup** | ||
- | {{: | + | {{: |
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
== Output setup == | == Output setup == | ||
Line 214: | Line 224: | ||
Go to the **Outputs configuration** | Go to the **Outputs configuration** | ||
- | {{: | + | {{: |
Then return to the main menu, go to the **Save settings** | Then return to the main menu, go to the **Save settings** | ||
- | ~~CL~~ | + | |
+ | ~~CL~~ | ||
==== Brake light setup ==== | ==== Brake light setup ==== | ||
The setting is carried out in the same way as for connecting and setting up the headlight, except for the section **Control from external buttons of the switch connected to the uLight board**. Also read the description of the **Brake signal setup** | The setting is carried out in the same way as for connecting and setting up the headlight, except for the section **Control from external buttons of the switch connected to the uLight board**. Also read the description of the **Brake signal setup** | ||
- | |||
==== Reverse signal setup ==== | ==== Reverse signal setup ==== | ||
Similar to connecting and setup the headlight. Also, read the description of the **Reverse signal setup** | Similar to connecting and setup the headlight. Also, read the description of the **Reverse signal setup** | ||
- | |||
==== Turn signal setup ==== | ==== Turn signal setup ==== | ||
Similar to connecting and setup the headlight. Also, read the description of the **Turn signal setup** | Similar to connecting and setup the headlight. Also, read the description of the **Turn signal setup** | ||
- | |||
==== Horn setup ==== | ==== Horn setup ==== | ||
Similar to connecting and setup the headlight. Also, read the description of the **Horn setup** | Similar to connecting and setup the headlight. Also, read the description of the **Horn setup** | ||
- | |||
==== Fan setup ==== | ==== Fan setup ==== | ||
- | Similar to connecting and setup the headlight. Also, read the description of the **Fan control** | + | Similar to connecting and setup the headlight. Also, read the description of the **Fan control** |
==== Temperature sensors setup ==== | ==== Temperature sensors setup ==== | ||
Read the description of the **Inputs configuration** | Read the description of the **Inputs configuration** | ||
- | |||
==== Throttle setup ==== | ==== Throttle setup ==== | ||
Connect the throttle levers according to the [[https:// | Connect the throttle levers according to the [[https:// | ||
- | |||
==== Brake setup ==== | ==== Brake setup ==== |