meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:firmware [2023/10/06 08:26]
dmitry
en:firmware [2024/04/08 08:38] (current)
vasilisk [2 Feb 2024]
Line 1: Line 1:
 ~~Title: Firmware~~ ~~Title: Firmware~~
  
-Copy files to the root directory of the microSD card with FAT32 filesystem (how to format microSD to FAT32 on Windows and Mac you can read [[https://www.lifewire.com/format-sd-card-to-fat32-6666166|here]]), insert into On-board computer (contacts on top) and run the update process.\\ 
 <WRAP important 60%>\\ <WRAP important 60%>\\
 **Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </WRAP> **Do not downgrade firmware that was installed by the manufacturer! You may get a brick** </WRAP>
Line 10: Line 9:
  
 If your On-board computer has firmware **v0.60B** or lower and Controller **v.7.18** and lower, first, need to update all devices but display. Because menu protocol is new and old devices will not be visible in the menu. After the update is finished hold the left button few seconds to exit the updated device menu. If the button does not work you may need to reset the power supply or replug CAN cable in the On-board computer. After everything is updated — update the On-board computer. Make a controller reset (load defaults) after the update. We recommend running motor detects again on controllers. Detection of throttle/brake connected to display should be done in the On-board computer menu. If your On-board computer has firmware **v0.60B** or lower and Controller **v.7.18** and lower, first, need to update all devices but display. Because menu protocol is new and old devices will not be visible in the menu. After the update is finished hold the left button few seconds to exit the updated device menu. If the button does not work you may need to reset the power supply or replug CAN cable in the On-board computer. After everything is updated — update the On-board computer. Make a controller reset (load defaults) after the update. We recommend running motor detects again on controllers. Detection of throttle/brake connected to display should be done in the On-board computer menu.
 +
 +Copy files to the root directory of the microSD card with FAT32 filesystem (how to format microSD to FAT32 on Windows and Mac you can read [[https://www.lifewire.com/format-sd-card-to-fat32-6666166|here]]), insert into On-board computer (contacts on top) and run the update process.\\
  
 Instruction of update of firmware:\\ Instruction of update of firmware:\\
Line 21: Line 22:
 3. [[:en:ulight#device_information|Information]] about the firmware version of the uLight. 3. [[:en:ulight#device_information|Information]] about the firmware version of the uLight.
  
-The list of actual firmware to be downloaded:+The list of actual firmware to be downloaded:\\ 
 +===== 8 April 2024 ===== 
 +**uLight v0.6.8** [[https://drive.google.com/file/d/1jCYlLt1iZDSI1UAnWz7-A2rj4AgU_0-h/view?usp=drive_link|{{:en:firmware:file.png?nolink&23x32}}]]\\ 
 +Unzip before update!\\ 
 +Added brake 'Brk' to button inputs for functions.\\ 
 +Removed reverse when CAN buttons active.\\ 
 + 
 + 
 +===== 2 Feb 2024 ===== 
 +**uLight v0.6.6** [[https://drive.google.com/file/d/1UuvFxdCsQaef-B8nJTGs6R1u6aOT_ZpW/view?usp=drive_link|{{:en:firmware:file.png?nolink&23x32}}]]\\ 
 +LEVCAN updated.\\ 
 +Added to functions 4 configurable signals with button input.\\ 
 +Added configurable logic: AND, NOT, OR, XOR, as another button type.\\ 
 + 
 +===== 22 Dec 2023 ===== 
 +**uLight v0.6.5** [[https://drive.google.com/file/d/1PTKczUdl8sG7CAF8gYwZN_qpFoxGPooY/view?usp=drive_link|{{:en:firmware:file.png?nolink&23x32}}]]\\ 
 +Small update:\\ 
 +Added brake button selection for only light indication without actual braking.\\ 
  
 ===== 30 September 2023 ===== ===== 30 September 2023 =====
Line 39: Line 58:
 Fixed active braking stutter\\ Fixed active braking stutter\\
 Adjusted square control duty cycle\\ Adjusted square control duty cycle\\
-</hidden></WRAP> +</hidden></WRAP>\\ 
-//+ 
 **Display v0.82B** [[https://drive.google.com/file/d/1gXyGXUsIkZL6e9F7os2gl7ZMKsPlCJWi/view?usp=sharing|{{:en:firmware:file.png?nolink&23x32}}]]\\ **Display v0.82B** [[https://drive.google.com/file/d/1gXyGXUsIkZL6e9F7os2gl7ZMKsPlCJWi/view?usp=sharing|{{:en:firmware:file.png?nolink&23x32}}]]\\
 <WRAP><hidden onHidden="Show change log"> Added access level menu support\\ <WRAP><hidden onHidden="Show change log"> Added access level menu support\\